Eshop roka 2025 s vykurovacou technikou

Ventil za pritisak GAS - 28 mm IVAR.IVN10 GAS

Kod: IVNGAS10.28
Nije ocijenjeno Detalji ocjene
11,09 € –20 %
Vykurovacia technika Nátrubok PRESS GAS - 28mm
11,09 € –20 % 8,87 € / kom 7,21 € bez PDV-a Izračunaj cijenu:
Međunarodna dostava
Na zalihi kod dobavljača

Detaljne informacije

Detaljan opis proizvoda

Natrubak PRESS GAS - 28 mm

 

  • PN 5, T = -20 °C do +70 °C
  • natrubak PRESS x PRESS
  • namijenjen za: distribuciju prirodnog plina, biopljina i propana u tečnom stanju
  • materijal: nehrđajući čelik Wst. Nr. 1.4404 (AISI 316L), tesnički O prsten HNBR žuti
  • certifikat SZÚ Brno, DVGW

Napomena: Dimenzije fitinzi PRESS GAS 76,1, 88,9
i 108 mm po narudžbi.

Često postavljana pitanja

  • Koje alatke trebam za montažu ovog fitinza? Press fitinzi zahtijevaju specijalizirane pres alatke s odgovarajućim tipom čeljusti (obično označeni kao B, F ili TH prema sistemu) koji odgovaraju dimenziji i tipu fitinza - bez odgovarajućeg alata se veza ne može izvršiti ni provjeriti.
  • Kako znam da je veza ispravno zalisana? Kvalitetni press fitinzi imaju indikator zalisivanja (npr. tesnički O prsten koji u slučaju nedovršenog lisovanja prelazi) - prije zatapanja u zid ili poterni sloj uvijek je potrebno izvršiti tlak test cijelog sustava.
  • Može li se veza nakon zalisivanja rastaviti? Ne, za razliku od vijenčanog (zavrnjenog) šrafbena, lisovana veza je trajna i za rastavljanje je potrebno odrezati fitinzi i zamijeniti novim.
  • Mora li montažu izvršiti stručnjak? Da, lisovanje fitinzi zahtijeva stručnost i ispravno kalibrirane alatke - preporučujemo da posao povjerite kuriru/inštalateru, posebno za veze koje će biti zatapane u zid ili poterni sloj bez mogućnosti buduće kontrole.

Dodatni parametri

Kategorija: IVAR.IVN10 GAS - spojnice PRESS GAS
Dostupnost: Na zalihi ili kod dobavljača
Zadnje ažuriranje cijene: 13.04.2026 1:03:21

Ocjena proizvoda

Budite prvi koji će objaviti članak na ovoj stavci!

Nemojte ispunjavati ovo polje

Kako biste ocijenili ovaj proizvod? Odaberite 1 do 5 zvjezdica, pri čemu 1 označava najlošiju, a 5 najbolju ocjenu.

Rasprava

Nemojte ispunjavati ovo polje

Popis rasprava

G Avatar autora 19.10.2026 13:55
I am trying to fix a gas pipe in my house and want to use this 28mm part, but I am not sure if I can just take it apart later if I make a mistake or if I need special tools to put it on?
A Avatar autora 19.10.2026 13:55
You will need special crimping pliers with the right jaws to install this fitting because you cannot press it by hand. Once it is pressed, the joint is permanent and cannot be taken apart; you would have to cut it out and replace it if something goes wrong. We strongly recommend hiring a professional plumber for this work, especially since it involves gas piping.

IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all “Made in Italy”.

 

Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.

 

Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.

 

“Made in Italy” adds value

IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all “Made in Italy”.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.

The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.

 

Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.

The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.


As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.

Vytvořil Shoptet | Design Shoptak.cz.