Eshop roka 2025 s vykurovacou technikou

Luk 90° PRESS GAS - 54 mm IVAR.IVN20 GAS

Kod: IVNGAS20.54
Nije ocijenjeno Detalji ocjene
69 € –20 %
Vykurovacia technika Oblúk 90° PRESS GAS - 54mm
69 € –20 % 55,20 € / kom 44,88 € bez PDV-a Izračunaj cijenu:
Međunarodna dostava
Na zalihi kod dobavljača

Detaljne informacije

Detaljan opis proizvoda

Luk 90° PRESS GAS - 54 mm

  • PN 5, T = -20 °C do +70 °C
  • luk 90° PRESS x PRESS
  • namijenjen: za distribuciju prirodnog plina, bioplinova i propana u tečnom stanju
  • materijal: nehrđajući čelik Wst. Nr. 1.4404 (AISI 316L), tesnički O prsten HNBR žuti
  • certifikat SZÚ Brno, DVGW

Napomena: Razmjeri fitinzi PRESS GAS 76,1, 88,9 i 108 mm po narudžbi.

Često postavljana pitanja

  • Koju alatu trebam za montažu ovog fitinza? Press fitinzi zahtijevaju specijalizirane press klešti s pravim tipom čeljusti (obično označeni kao B, F ili TH prema sistemu) koji odgovaraju dimenziji i tipu fitinza - bez prave alate ne može se stvoriti ni provjeriti spoj.
  • Kako znam da je spoj ispravno zalisan? Kvalitetni press fitinzi imaju indikator zalisavanja (npr. tesnički O prsten koji pri nedovršenom lisovanju preteče) - prije zatvaranja u zid ili pod je uvijek potrebno izvršiti tlak test cijelog sustava.
  • Može li se spoj rastaviti nakon zalisavanja? Ne, za razliku od vijenčanog (zavrnjenog) spoja, lisovani spoj je trajan i njegovo rastavljanje zahtijeva odrezati fitinzi i zamijeniti novim.
  • Mora li montažu izvršiti stručnjak? Da, lisovanje fitinzi zahtijeva stručnost i ispravno kalibriranu alatu - preporučujemo da to ostavite grijaniku/instalateru, posebno za spojeve koji će biti zatvoreni u zidu ili podu bez mogućnosti kasnije kontrole.

Dodatni parametri

Kategorija: IVAR.IVN20 GAS - lukovi 90° FF PRESS GAS
Dostupnost: Na zalihi ili kod dobavljača
Zadnje ažuriranje cijene: 13.04.2026 1:10:43

Ocjena proizvoda

Budite prvi koji će objaviti članak na ovoj stavci!

Nemojte ispunjavati ovo polje

Kako biste ocijenili ovaj proizvod? Odaberite 1 do 5 zvjezdica, pri čemu 1 označava najlošiju, a 5 najbolju ocjenu.

Rasprava

Nemojte ispunjavati ovo polje

Popis rasprava

M Avatar autora 17.11.2026 16:31
Könnten Sie mir bitte mitteilen, ob der Dichtungsring aus HNBR dauerhaft für den Einsatz mit Propan in flüssiger Phase geeignet ist, oder ist dies nur für den kurzzeitigen Kontakt vorgesehen? Zudem bitte ich um Bestätigung, ob der zulässige Temperaturbereich von -20 °C bis +70 °C auch bei durchgehendem Betrieb an der unteren Grenze eingehalten werden kann.
A Avatar autora 17.11.2026 16:31
Der Dichtungsring aus HNBR ist laut Spezifikation für den dauerhaften Einsatz mit Erdgas, Biogas und Propan in flüssiger Phase ausgelegt, nicht nur für kurzzeitigen Kontakt. Der angegebene Temperaturbereich von -20 °C bis +70 °C gilt für den regulären Betrieb des Fittings, also auch durchgehend an der unteren Grenze. Das Material des Bogens selbst ist rostfreier Stahl 1.4404 (AISI 316L), zertifiziert nach SZÚ Brno und DVGW.
P Avatar autora 31.10.2026 22:39
Grüß Gott, kann ich für diesen 54 mm Bogen eine normale B-Pressbacke verwenden, oder brauch ich für Gas-Fittings eine spezielle Zange? Und hält die Pressverbindung bei Propan in flüssiger Phase überhaupt dicht?
A Avatar autora 31.10.2026 22:39
Grüß Gott Patrick, welche Zangentype genau passt, hängt vom System des Fittings ab - das sollten Sie bzw. Ihr Installateur vorher prüfen, da ohne den passenden Zangentyp die Verbindung nicht ordentlich gepresst und auch nicht kontrolliert werden kann. Zur Dichtheit: Der Bogen ist mit HNBR-Dichtring ausgestattet und laut Spezifikation für Erdgas, Biogas und Propan in flüssiger Phase ausgelegt, PN 5, Temperaturbereich -20°C bis +70°C. Wichtig ist in jedem Fall ein Drucktest des gesamten Systems vor dem Einbau in Wand oder Estrich, und die Montage sollte ein Fachmann mit kalibriertem Werkzeug übernehmen.

IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all “Made in Italy”.

 

Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.

 

Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.

 

“Made in Italy” adds value

IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all “Made in Italy”.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.

The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.

 

Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.

The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.


As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.

Vytvořil Shoptet | Design Shoptak.cz.